Gauge Minitrix - Article No. 66857
Model train Locomotive Decoder 1000 Milliamps for MTC14 Interface
This is a receiver for all DC locomotives with a total current draw of up to 1000 milliamps (motor 1000 milliamps, each light 200 milliamps). It can be used for digital locomotives with an mtc14 digital interface. The decoder can be used in the formats Selectrix 1, Selectrix 2, and DCC. It automatically recognizes analog operation. The decoder has automatic load control. There are connections for a light function. There are connections for auxiliary functions (Aux1 and Aux2). The decoder has protection of the motor outputs against short circuits. Advanced Selectrix 1 programming of additional settings can be done by selecting address "00", example: finer gradation of the pulse widths (control variations), reversing polarity for direction of travel. In Selectrix operation: 31 speed levels. 111 addresses. DCC operation: speed level selection 14/28/126 speed levels. Addresses can be selected as short up to 127 and long up to 10239. Braking operation in the formats DCC and SX: DC same/opposed polarity, braking diodes, asymmetric track signal, braking generators. Dimensions approximately 14 x 9 x 2 mm / 9/16" x 11/32" x 1/16".
Sturdy multi-protocol retrofit decoder, protected against short circuits between the motor and the track; safety shutoff in the event of excess current, excess temperature, and short circuits; newly developed motor control for extremely smooth operation of all currently available DC motors; operation continued at the same speed after current interruption of up to 1 second; SUSI-controlled acceleration delay (SUSI-WAIT); one or two-part braking sections. Special characteristics in analog operation: acceleration voltage can be set very low, maximum speed limit, dynamic dimming of lights and AUX dependent on track voltage, programmable functions, typical analog running behavior.
Epoch: | ---------- |
Features: | ---------- |
Gauge: | Minitrix |
Pictograms: | % \ ¥ |
Warnings: | only for adults |
WEEE-Reg.-Nr.: | DE30519521 |
*There is a manufacturer's warranty on the part of the guarantor Gebr. Märklin & Cie. GmbH, Stuttgarter Str. 55-57, 73033 Göppingen with a duration of 2 years. The corresponding warranty conditions can be found here.
Item No.: 66623 Model train Minitrix and Z Gauge Locomotive Wheel Cleaning Brush
incl. VAT plus shipping
Item No.: 24612 Model train Märklin Right Turnout Length 188.3 mm / 7-13/32"
incl. VAT plus shipping
Item No.: 24230 Model train Märklin Curved C Track Radius R2 = 437.5 mm / 17-1/4" / 30°
Item No.: 74462 Model train Installation Digital Decoder for Turnouts (C Track)
incl. VAT shipping
Item No.: 24997 Model train Märklin Uncoupler Track Length 94.2 mm / 3-11/16"
incl. VAT shipping
Item No.: 24672 Model train Märklin Right Curved Turnout Radius 360 mm / 14-3/16"
incl. VAT plus shipping
Item No.: 24206 Model train Märklin Curved C Track Radius R2 = 437.5 mm / 17-1/4" / 5.7°
Item No.: 62612 Model train Right Turnout 188,3 mm / 24,3° / 437,5 mm
incl. VAT plus shipping
Item No.: 74470 Model train Turnout Lantern Kit, Right/Left (Contents 1 piece of each)
Item No.: 24978 Model train Märklin Track End with a Bumper Length 77.5 mm + 5 mm /...
incl. VAT plus shipping
Item No.: 24611 Model train Märklin Left Turnout Length 188.3 mm / 7-13/32"
incl. VAT plus shipping
Item No.: 24107 Model train Märklin Curved C Track Radius R1 = 360 mm / 14-3/16" / 7.5°
Item No.: 66856 Model train Locomotive Decoder, mtc 14-Pin Interface Connector
incl. VAT shipping
Item No.: 66623 Model train Minitrix and Z Gauge Locomotive Wheel Cleaning Brush
incl. VAT plus shipping
Item No.: 60760 Model train Digital High Efficiency Propulsion Set
incl. VAT shipping
Item No.: 11158 Model train "Freight Train" Digital Starter Set with a Class 120
incl. VAT shipping